Get in touch with us

COPA-DATA USA

COPA-DATA USA Corp.

186 Princeton-Hightstown Rd., Bldg 4

Princeton Junction, NJ 08550

United States

Tel.: +1 (609) 385 0830

Fax: +1 (609) 385 0829

E-mail: sales.us@copadata.com

Contact Page

zenon Driver Information

zenon Driver
3S
Codesys Arti NG driver
Codesys Soft PLC driver "New Generation" for the Codesys 3S-ARTI (Asynchron Runtime Interface) interface. The driver supports direct variable import from the Codesys development environment and replaces the Codesys Arti Soft PLC driver.
3S
3S v3 driver for PLC Handler
3S V3 driver to communicate to CoDeSys v3 based PLCs via PLC Handler. The driver uses the realtime time stamping in the PLC. Therefore a time synchronisation betwenn PLC and SCADA system is mandatory.
ABB
Driver for ABB 07KT94
serial driver for ABB 07KT94 PLCs
ABB
Modbus RTU and Open Modbus TCP
The driver supports the protocol "Modbus RTU" over a serial connection and over a TCP/IP connection and the protocol "Open Modbus TCP" for TCP/IP connection. The driver acts as a Modbus Master. (For a Modbus Slave please use the Process Gateway)
ABB
IEC 61850 driver
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
ABB
Modbus Energy driver
Open Modbus TCP/IP driver with the following differences compared to the standard Modbus driver: - TCP/IP channel bundling - improved communication with gateways - read and write only for holding register - supports only Open Modbus TCP/IP protocol - Sequence of Events for AREVA MiCOM 126/127, GE Multilin F650, GE Multilin UR-series, ICE NPx800, Schneider MODICON TSX Premium with COSTRONIC Software www.areva-td.com, www.gedigitalenergy.com, www.groupeice.com, www.costronic.ch
ABB
IEC 61400-25-4 C
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
Actisense
Driver for NMEA 2000 Bus
Driver to communicate with components connected to a NMEA 2000 bus system. The driver uses the NGT-1 NMEA 2000 to PC Interface from Actisense. (www.actisense.com)
Allen-Bradley
Allen Bradley RS-Linx driver
Supports all connections which are available with RS Linx (http://www.software.rockwell.com)
Allen-Bradley
Allen Bradley DF1-driver
For all Allen Bradley PLCs supporting DF1. The driver works half duplex
Allen-Bradley
Allen-Bradley ODVA driver
Ethernet/IP driver for communication via Common Industrial Protocol - CIP from Open DeviceNet Vendor Organisation (ODVA) with Allen-Bradley Control-Logix and Compact-Logix PLCs. (For Micro-Logix PLCs please use the 'AllenBradleyDF1' driver) The driver supports direct browsing of variables from the PLC, offline browsing from projectfile (*.L5K) and blockread/write for all datatypes including structures and arrays. Www.ab.com
Alstom
IEC 60870-5-101_104
Driver for the IEC 60870-5-101 (serial) and the IEC 60870-5-104 (TCP/IP) protocol; a Master (controlling station)
Applicom
Applicom IO configuration
Driver for Applicom IO cards (Direct Link)
Areva
Modbus RTU and Open Modbus TCP
The driver supports the protocol "Modbus RTU" over a serial connection and over a TCP/IP connection and the protocol "Open Modbus TCP" for TCP/IP connection. The driver acts as a Modbus Master. (For a Modbus Slave please use the Process Gateway)
Areva
IEC 60870-5-101_104
Driver for the IEC 60870-5-101 (serial) and the IEC 60870-5-104 (TCP/IP) protocol; a Master (controlling station)
Areva
Modbus Energy driver
Open Modbus TCP/IP driver with the following differences compared to the standard Modbus driver: - TCP/IP channel bundling - improved communication with gateways - read and write only for holding register - supports only Open Modbus TCP/IP protocol - Sequence of Events for AREVA MiCOM 126/127, GE Multilin F650, GE Multilin UR-series, ICE NPx800, Schneider MODICON TSX Premium with COSTRONIC Software www.areva-td.com, www.gedigitalenergy.com, www.groupeice.com, www.costronic.ch
Asfinag
SaNORS - SOS-telephones
SaNORS (Standard asfinag emergency call interface) - driver for the Asfinag SOS-telephones (www.asfinag.net)
Bachmann
Bachmann M1 driver
Direct TCP/IP driver for Bachmann M1 PLCs (www.bachmann.at)
BACnet
BACnet driver Next Generation
This driver comunicates to one or more BACnet devices (BACnet-Automation stations) using BACnet/IP protocol. The connected BACnet devices have to be operated as BACnet servers. The driver implements only client functionalities.
Beckhoff
Beckhoff BC-BK 9000
Driver for Beckhoff BC/BK9000. The driver is based on the TC-ADS interface and uses a protocol optimized for the bus clamps.
Beckhoff
Beckhoff TwinCat NG driver
Beckhoff TwinCAT driver "New generation" for TwinCAT Soft PLC 2.6 and higher. The driver is based on the TC-ADS interface. The driver replaces the Beckhoff TC-ADS and the Beckhhoff ADS driver. A conversion wizard is available. The TC-ADS software has to be installed.
Beckhoff
K-Bus driver for CX1000
Driver for Beckhoff CX1000 with K-Bus
Bernecker + Rainer
Mininet driver
Mininet Master driver for B+R PLCs (www.br-automation.com)
Bernecker + Rainer
BR TCP-IP
Driver for B+R Burklimat or B+R System 2000 PLCs. Needs no PVI software but a special handling-modul in the PLC witch can only orderd from B+R . (www.br-automation.com)
Bernecker + Rainer
BR-PVI driver
Up to date Bernecker and Rainer driver based on PVI interface from Bernecker and Rainer. The variables can either be imported online from the PLC or offline form the B&R OPC interface. Communication parameters are stored at each variable. The driver supports spontaneous data exchange and hysteresis. (www.br-automation.com)
Bernecker + Rainer
BR Transponder Reader 4102/4150
Driver for Bernercker and Rainer RFID Transponder Reader 4102/4150 (BuR Modell number: 5E9000.29) with USB interface.
Biffi-Tyco Flow Control
Biffi DCM
Driver for comunication with a redundant Biffi DCM Master station. (www.biffi.it)
Bihl+Widemann
AS-interface
For Bihl+Widemann AS-i configurations
Bosch Rexroth
3S v3 driver for PLC Handler
3S V3 driver to communicate to CoDeSys v3 based PLCs via PLC Handler. The driver uses the realtime time stamping in the PLC. Therefore a time synchronisation betwenn PLC and SCADA system is mandatory.
Brodersen
System 2000
Driver for Brodersen RTUs (www.brodersencontrols.com)
Brodersen
SYSTEM2000 LOGGING
Driver for Brodersen RTUs with logging mechanisms. Supports the functionality of reading historical (logged) data. (www.brodersencontrols.com)
Brodersen
straton / zenonLogic driver
Driver for connection to straton or zenonLogic
Brodersen
Passive Modbus RTU driver
The driver waits on a TCP/IP port, until the Brodersen Gateway establishes a GPRS connection. Then it communicates via Modbus RTU. (www.brodersencontrols.com)
Brodersen
Brodersen IOTOOLS
--
Brodersen
straton NG driver
Driver for communication with straton / zenonLogic PLCs. Replaces straton 32 driver. The driver can use several connections at the same time and uses an improved communication concept.
Buderus
Buderus32
The driver communicates via the module KM471with connected ECOCAN-BUS modules. (http://www.heiztechnik.buderus.de)
CAN
Generic driver for CAN bus
Driver for generic CAN communication. The driver reads and writes the 8 data bytes of the standard CAN telegram. A CANUSB adapter from Lawicel AB is required (www.canusb.com)
CIMON
Modbus RTU and Open Modbus TCP
The driver supports the protocol "Modbus RTU" over a serial connection and over a TCP/IP connection and the protocol "Open Modbus TCP" for TCP/IP connection. The driver acts as a Modbus Master. (For a Modbus Slave please use the Process Gateway)
COPA-DATA
Archive driver
Writes data cyclically to the harddisk in RAW format. (Only values, no timestamps, no status information). The data have to be opened / further processed with external tools. (Tools only as examples available from COPA-DATA)
COPA-DATA
File driver
Data exchange with external programs on file basis. Values are read from a file and displayed resp. archived in zenon. Values can also be written into a file by zenon.
COPA-DATA
OPC Client V2-0
Driver for the communication with OPC Servers.
COPA-DATA
SQL Driver
The driver is used for the bidirectional data exchange with a SQL database supporting ODBC.
COPA-DATA
DDE Client driver
Driver for the data exchange with applications supporting DDE. Also supports NET DDE.
COPA-DATA
straton to zenon RT connection
Internal straton peripheral driver - Shared Memory dreiber; may only be use once on a computer! This driver must be configured in the straton project if a zenon variable is set to "externally visible"
COPA-DATA
Win32 Shared memory
Driver for so called super-global variables exchanged between two zenonLogic or straton RT instances
COPA-DATA
OPC UA Client driver
Driver for comunication with all OPC-UA (Unified Architecture) servers. The driver supports only Data Access (DA). www.opcfoundation.org
COPA-DATA
Remote Runtime driver
Driver for read only communication to a remote Runtime system. Remote Runtimes will be supported through all versions starting with version 5.50. At the remote system no project adaption is necessary.
Copalp
straton / zenonLogic driver
Driver for connection to straton or zenonLogic
Copalp
straton NG driver
Driver for communication with straton / zenonLogic PLCs. Replaces straton 32 driver. The driver can use several connections at the same time and uses an improved communication concept.
Costronic
Modbus Energy driver
Open Modbus TCP/IP driver with the following differences compared to the standard Modbus driver: - TCP/IP channel bundling - improved communication with gateways - read and write only for holding register - supports only Open Modbus TCP/IP protocol - Sequence of Events for AREVA MiCOM 126/127, GE Multilin F650, GE Multilin UR-series, ICE NPx800, Schneider MODICON TSX Premium with COSTRONIC Software www.areva-td.com, www.gedigitalenergy.com, www.groupeice.com, www.costronic.ch
CTI
TI 505 - 545 driver
Driver for Texas Instruments TI 505 / 545. Protocols: TBP,NITP, TCP/IP
CTI
CTI driver
Driver for CTI PLCs,, Texas Instruments TI 505 PLCs or Simatic 545/555 PLCs. The driver support the protocols CAMP and NITP with Packed Task Codes.
Daimler
integra driver
Driver for communication to Siemens S7 PLCs via the integra standard control room interface from Daimler AG
Database
Archive driver
Writes data cyclically to the harddisk in RAW format. (Only values, no timestamps, no status information). The data have to be opened / further processed with external tools. (Tools only as examples available from COPA-DATA)
Database
SQL Driver
The driver is used for the bidirectional data exchange with a SQL database supporting ODBC.
Dateien
Archive driver
Writes data cyclically to the harddisk in RAW format. (Only values, no timestamps, no status information). The data have to be opened / further processed with external tools. (Tools only as examples available from COPA-DATA)
Dateien
File driver
Data exchange with external programs on file basis. Values are read from a file and displayed resp. archived in zenon. Values can also be written into a file by zenon.
Dateien
DDE Client driver
Driver for the data exchange with applications supporting DDE. Also supports NET DDE.
DNP3
-
zenonLogic driver for communication with DNP3 master
DNP3
DNP3 third generation driver
Connection to DNP3 Outstations; replaces the previous DNP332 and DNP3_NG driver. See driver documentation for information in regard to switching from the DNP332/DNP3_NG driver to the DNP3_TG driver
Echelon
LON
Driver for the communication with LON nodes.
Echelon
i-LON 100
Driver for the communication with LON nodes via iLon100 router from Echelon. (www.echelon.com)
EIB
EIB-KNX bus driver
Driver for the communication with the European Installation Bus (EIB / KNX). In the Runtime the driver needs the Falcon Runtime.
Elau
Codesys Arti NG driver
Codesys Soft PLC driver "New Generation" for the Codesys 3S-ARTI (Asynchron Runtime Interface) interface. The driver supports direct variable import from the Codesys development environment and replaces the Codesys Arti Soft PLC driver.
Elau
3S v3 driver for PLC Handler
3S V3 driver to communicate to CoDeSys v3 based PLCs via PLC Handler. The driver uses the realtime time stamping in the PLC. Therefore a time synchronisation betwenn PLC and SCADA system is mandatory.
ESA
Driver for ESA PCI CIB
Driver for ESA Windows CE terminal including ESA PCI CIB communication card for Windows CE for the communication with PLCs supporting MPI.
Esser
Driver for Esser BMZ 8000
Driver for fire alarm system Esser BMZ 8000. The driver only supports reading access. (http://www.igs-hagen.de/brandzentralen.htm)
Euchner
Euchner Ident
Driver for Euchner chip card ident system (www.euchner.de)
Festo
Festo EasyIP Multiprog
EasyIP driver for Festo IPC/FEC, Multiprog programming. (www.festo.com)
Festo
Festo Serial-CI, FST
Serial/CI driver for Festo FPC/IPC/FEC, FST programming. Uses testing system of the FST kernel. (www.festo.com)
Files
Archive driver
Writes data cyclically to the harddisk in RAW format. (Only values, no timestamps, no status information). The data have to be opened / further processed with external tools. (Tools only as examples available from COPA-DATA)
Files
File driver
Data exchange with external programs on file basis. Values are read from a file and displayed resp. archived in zenon. Values can also be written into a file by zenon.
Files
DDE Client driver
Driver for the data exchange with applications supporting DDE. Also supports NET DDE.
Gantner
Modbus RTU and Open Modbus TCP
The driver supports the protocol "Modbus RTU" over a serial connection and over a TCP/IP connection and the protocol "Open Modbus TCP" for TCP/IP connection. The driver acts as a Modbus Master. (For a Modbus Slave please use the Process Gateway)
GE Automation&Controls
Modbus Energy driver
Open Modbus TCP/IP driver with the following differences compared to the standard Modbus driver: - TCP/IP channel bundling - improved communication with gateways - read and write only for holding register - supports only Open Modbus TCP/IP protocol - Sequence of Events for AREVA MiCOM 126/127, GE Multilin F650, GE Multilin UR-series, ICE NPx800, Schneider MODICON TSX Premium with COSTRONIC Software www.areva-td.com, www.gedigitalenergy.com, www.groupeice.com, www.costronic.ch
GE Automation&Controls
GE - SRTP driver
Communication to GE PLCs via the Service Request Transfer Protocol - SRTP. Almost all devices equipped with a ethernet port from GE Automation&Controls support SRTP. www.geautomation.com
GE Multilin
Modbus RTU and Open Modbus TCP
The driver supports the protocol "Modbus RTU" over a serial connection and over a TCP/IP connection and the protocol "Open Modbus TCP" for TCP/IP connection. The driver acts as a Modbus Master. (For a Modbus Slave please use the Process Gateway)
GE Multilin
IEC 61850 driver
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
GE Multilin
Modbus Energy driver
Open Modbus TCP/IP driver with the following differences compared to the standard Modbus driver: - TCP/IP channel bundling - improved communication with gateways - read and write only for holding register - supports only Open Modbus TCP/IP protocol - Sequence of Events for AREVA MiCOM 126/127, GE Multilin F650, GE Multilin UR-series, ICE NPx800, Schneider MODICON TSX Premium with COSTRONIC Software www.areva-td.com, www.gedigitalenergy.com, www.groupeice.com, www.costronic.ch
GE Multilin
IEC 61400-25-4 C
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
Gossen Metrawatt
Metrawatt driver
Driver for the Gossen-Metrawatt energy control systems U160x. The driver can read energy and measured data
Helmholz
HMI driver
Driver for the MPI->HMI adapter from Siemens or Helmholz
Helmholz
Hilscher MPI driver
Driver for Hilscher Netlink Adapter (MPI -> TCP/IP) or Hilscher CIF-PB cards. The Netlink Adapter is also available identical in construction from IBH and Helmholz. (http://www.hilscher.com)
Helmholz
3964R-RK512
Driver for 3964R/RK512
Helmholz
PC Adapter - Vipa Green Cable
For the serial communication via the Siemens PC adapter / Helmholz PC adapter to Siemens and Vipa PLCs with MPI interface. Alternativ: Serial communication to Vipa PLCs via the Vipa Green Cable to the Vipa PD interface.
Hilscher
Hilscher MPI driver
Driver for Hilscher Netlink Adapter (MPI -> TCP/IP) or Hilscher CIF-PB cards. The Netlink Adapter is also available identical in construction from IBH and Helmholz. (http://www.hilscher.com)
Hilscher
Hilscher CIF driver
Generic CIF driver for Interbus and Profibus DP cards from Hilscher (www.hilscher.com). The driver can be configured as master or as slave and communicates with the bus participants on the data level without protocol.
Hilscher
Hilscher CIF Profibus
Driver for Hilscher Profibus DP cards (CIF 30, 40, 50, 60, 104). The configuration is done via zenon Logic fieldbus configurator.
Hilscher
Hilscher SYCON configuration
Driver for Hilscher Fieldbuscards, the configuration is done via Hilscher configuration software "SyCon". The configuration is exported with SyCon and importet in the zenonLogic fieldbus configurator.
Hilscher
Hilscher SYCON configuration
Treiber for Hilscher fieldbus boards, the configuration is done via the Hilscher configuration software "SyCon". The SyCon configuration file has to be imported in the zenonLogic fieldbus configuration.
Hilscher
Hilscher SYCON CifX
Driver for Hilscher fieldbus boards; the configuration is doen via Hilscher configuration software "SYCON.net". The configuration file has to be exported as XML in SYCON.net and imported in zenonLogic fieldbus configuration.
Hitachi
Hitachi
COMM-H driver (www.hitachi.com)
HMS
HMS configuration
Driver for HMS fieldbus cards, the configuration is done via HMS cKonfiguration software
Hydrometer
Hydrometer Driver
The Hydrometer driver connects to IZAR Center (made by Hydrometer GmbH). The IZAR Center connects either M-Bus devices or Hydrometer radio receivers. The radio receivers (M-Bus Receiver 868) are reading remote devices in ist range. (www.hydrometer.de)
IBH
Hilscher MPI driver
Driver for Hilscher Netlink Adapter (MPI -> TCP/IP) or Hilscher CIF-PB cards. The Netlink Adapter is also available identical in construction from IBH and Helmholz. (http://www.hilscher.com)
IBH
IBH Soft PLC
The driver supports the Siemens S5 and S7 compatible Soft PLC from IBH (www.IBHsoftec.de)
ICE
Modbus Energy driver
Open Modbus TCP/IP driver with the following differences compared to the standard Modbus driver: - TCP/IP channel bundling - improved communication with gateways - read and write only for holding register - supports only Open Modbus TCP/IP protocol - Sequence of Events for AREVA MiCOM 126/127, GE Multilin F650, GE Multilin UR-series, ICE NPx800, Schneider MODICON TSX Premium with COSTRONIC Software www.areva-td.com, www.gedigitalenergy.com, www.groupeice.com, www.costronic.ch
Idec
Idec
Driver for Idec MicroSmart,OpneNet Controller and FC4A-HPC1. (www.idec.com)
IEC
IEC 60870-5-101_104
Driver for the IEC 60870-5-101 (serial) and the IEC 60870-5-104 (TCP/IP) protocol; a Master (controlling station)
IEC
IEC 61850 driver
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
IEC
IEC60870 103
Treiber für IEC60870 -5- 103 communication
IEC
IEC-62056-21 Driver
Driver for read out of values from energy meters. The driver uses mode C of IEC 62056-21 specification. The driver supports read only comunication.
IEC
IEC 61850 Server (Slave)
zenonLogic IEC 61850 Server driver (Slave). The driver supports the following IEC 61850 features: - Multiple connections to IEC 61850 clients via TCP/IP - Browse the data model (Logical Devices, Logical Nodes, Data Objects and Data Attributes) - Read and write of Data values - Read and write of Data Set values - Create and delete dynamically Data Sets - Control Model (all models) - Reporting (buffered and unbuffered) - File transfer - GOOSE protocol
IEC
IEC 61850 Client (Master)
zenonLogic IEC 61850 Client driver (Master) . The driver supports the following features: - Browse the data model (Logical Devices, Logical Nodes, Data Objects and Data Attributes) - Read and write of Data values - Read and write of Data Set values - Create and delete dynamically Data Sets - Control Model (all models) - Reporting (buffered and unbuffered) - File transfer
IEC
IEC60870-5-101/104 Slave
zenonLogic Slave driver for comunication with an IEC60870-5-101 or IEC60870-5-104 Master
IEC
IEC 61499 driver
The driver uses a communication protocol (SSCP) developed by COPA-DATA. The protocol is used for a spontaneous communication via TCP/IP to IEC 61499 controls. The protocol specification disclosed in the driver documentation and can be implemented easily for each control.
IEC
IEC 61400-25-4 C
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
Inat
S5 H1
H1 protocol driver for Siemens S5. H1 resp. "Industrial Ethernet" is the protocol name for the cellular network, which is based on the 7-layer-model of the ISO/OSI standard. (www.vipa.de, www.siemens.de, www.inat.de). At PC you need the PC H1 Driver from INAT.
Inat
S5 TCP-IP
Driver for the S5 TCP/IP communication. The driver supports polling (SEND/RECEIVE) and spontaneous communication (FETCH/WRITE). (www.vipa.de, www.siemens.de, www.inat.de, www.process-informatik.de)
Inat
S7 TCP-IP
Driver for S7 TCP/IP connection via standard network card without additional software. The driver supports Simatic PDiag. (www.siemens.com)
Inat
S7 driver Softnet
Driver for S7 PLCs via MPI / H1 / Profibus DP / TCP/IP. Based on the software SIMATIC NET (Softnet) from Siemens. (www.siemens.com)
Interbus
Interbus S driver
Driver for Interbus S Generation 4, Based on Interbus PC cards from Phönix Contact (www.phoenixcontact.com).
Interbus
CP001 Gateway driver
Driver for the Keba / Hilscher Universal Bus Gatway CP001. Supports communication via Profibus, Interbus usw.
Interbus
Hilscher CIF driver
Generic CIF driver for Interbus and Profibus DP cards from Hilscher (www.hilscher.com). The driver can be configured as master or as slave and communicates with the bus participants on the data level without protocol.
Internal driver
Driver for system variables
zenon System driver for displaying internal project information, network information, hardware information of the PC etc. The driver does not use up I/Os or TAGs.
Internal driver
Driver for simulator variables
zenon Simulation driver for simulation and internal variables. Variables also can be saved remant. The driver does not use up I/Os or TAGs.
Internal driver
Driver for Mathematics variable
zenon Mathematics driver. For numerical and binary operations. The driver does not use up I/Os or TAGs.
Internal driver
Driver for internal variables
Driver for internal variables. Variables can be local resp. global and can be started with an initial value or with the last value (remanence). The driver does not use up I/Os or TAGs.
Jetter
Jetter Treiber
Driver for comminication to Jetter PLCs via serial Interface, JETWay, PCPPLC, and via Ethernet UDP/TCP (JetIP/JetSTX) www.jetter.de
Kaba
Kaba data point server driver
Connection to the Kaba exos 9300 access management system via a data point server. www.kaba.com
Kalki
IEC 61850 driver
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
Kalki
IEC 61400-25-4 C
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
Keba
CP001 Gateway driver
Driver for the Keba / Hilscher Universal Bus Gatway CP001. Supports communication via Profibus, Interbus usw.
Keba
Ketop driver
Driver for the buttons on the Ketop T100 and T50
Keba
Kemro User ID Driver
Driver for comunication with the Kemro User ID USB Interface. The driver can read out datat from Keba RFID Chips. The driver is only available from Keba directly in combination with the hardware. (www.keba.com)
KEPCO
Kepco KDNP1 driver
Driver for communication with outstations via KDNP1 protocol from KEPCO. The protocol is based on the DNP3 protocol. The driver acts as master. On protocol level it supports serial communication and TCP/IP-communication to different outstations.
Kieback + Peter
BACnet driver Next Generation
This driver comunicates to one or more BACnet devices (BACnet-Automation stations) using BACnet/IP protocol. The connected BACnet devices have to be operated as BACnet servers. The driver implements only client functionalities.
KNX
EIB-KNX bus driver
Driver for the communication with the European Installation Bus (EIB / KNX). In the Runtime the driver needs the Falcon Runtime.
Kontron
ThinkIO/IOSystem758
Driver for Wago I/O System 758 (Wago IPC) bzw. Kontron ThinkIO with Windwos CE 5.0
Koyo
KOYO Sequence driver
Driver for the Koyo Sequence models (www.koyoele.co.jp/english)
Kuka Robotics
Phoenix Contact driver
Direct driver for all ProConOS based Controll systems from Phoenix Contact. Www.phoenixcontact.com
Kuka Robotics
Driver for Kuka Robots
The driver communicates directly with the Kuka robot control software Cross3KRC. It can drectly read and write variables of the robot.
KW-Software
Phoenix Contact driver
Direct driver for all ProConOS based Controll systems from Phoenix Contact. Www.phoenixcontact.com
Laetus
VDMA-XML driver
Driver for comunication with devices in packaging and process industry using VDMAXML_P Protocoll e.g.: Laetus components. Www.vdma.org, www.laetus.com
Lauer
Lauer PCS812
Driver for PCS812 communication box from Lauer for communication via MPI. (www.systeme-lauer.de)
Lauer
PCS807 Profibus DP
Driver for PCS807 communication box from Lauer for communication via ProfibusDP. (www.systeme-lauer.de)
Lawicel
Generic driver for CAN bus
Driver for generic CAN communication. The driver reads and writes the 8 data bytes of the standard CAN telegram. A CANUSB adapter from Lawicel AB is required (www.canusb.com)
LON
LON
Driver for the communication with LON nodes.
LON
i-LON 100
Driver for the communication with LON nodes via iLon100 router from Echelon. (www.echelon.com)
LSIS
LS Industrial Systems-XGT
For XGT series PLC from LS Industrial Systems. For Input and Output, symbolic und direct variables. Suppeort numerical data types from 1 Bit up to 8 Byte (eng.lsis.biz).
Mastervolt
MasterBus driver
Driver for the communication with a MasterBus system via MasterBus Modbus Interface from Mastervolt (www.mastervolt.com)
Matsushita
Panasonic serial
Driver for Panasonic (former Matsushita) FPx PLCs (www.panasonic-electric-works.com). The driver also supports modem connection.
Matsushita
Matsushita TCP-IP
TCP/IP driver for Matsushita FPx PLCs via standard network card. (www.matsushita.de)
M-Bus
Standard M-Bus
Driver for the standard M-Bus protocol.
Metrawatt
Metrawatt driver
Driver for the Gossen-Metrawatt energy control systems U160x. The driver can read energy and measured data
Microsoft
Azure driver
Driver for read only communication to Microsoft Azure Service Bus in the Cloud. Data can be written with the Azure Gateway to the MS Azure Service Bus and can be read afterwards back with the driver to another system. Usable for cross-plant communication without required opened TCP/IP ports.
Mitsubishi
Mitsubishi - Melsec A-Q
Driver for Mitsubishi A and Q series. (http://www.meau.com)
Mitsubishi
Mitsubishi - Melsec FX
Driver for Mitsubishi FX series. (http://www.meau.com)
Modbus RTU
Modbus RTU and Open Modbus TCP
The driver supports the protocol "Modbus RTU" over a serial connection and over a TCP/IP connection and the protocol "Open Modbus TCP" for TCP/IP connection. The driver acts as a Modbus Master. (For a Modbus Slave please use the Process Gateway)
Modbus RTU
Passive Modbus RTU driver
The driver waits on a TCP/IP port, until the Brodersen Gateway establishes a GPRS connection. Then it communicates via Modbus RTU. (www.brodersencontrols.com)
Modbus RTU
Modbus Energy driver
Open Modbus TCP/IP driver with the following differences compared to the standard Modbus driver: - TCP/IP channel bundling - improved communication with gateways - read and write only for holding register - supports only Open Modbus TCP/IP protocol - Sequence of Events for AREVA MiCOM 126/127, GE Multilin F650, GE Multilin UR-series, ICE NPx800, Schneider MODICON TSX Premium with COSTRONIC Software www.areva-td.com, www.gedigitalenergy.com, www.groupeice.com, www.costronic.ch
Modicon
Modicon TSX
Connection to Modicon TSX PLC via Unitelway protocol. (www.schneider-electric.de)
Moeller
Moeller PSUNI
Driver for Klöckner+Moeller PLCs. (www.moeller.net)
Moeller
Profibus DP Master driver
Developed for special Moeller Profibus DP participant. Also can communicate with other passive Profibus DP participants. Better alternative: zenonLogic with Profibus DP driver.
Moeller
Codesys Arti NG driver
Codesys Soft PLC driver "New Generation" for the Codesys 3S-ARTI (Asynchron Runtime Interface) interface. The driver supports direct variable import from the Codesys development environment and replaces the Codesys Arti Soft PLC driver.
Mondial
Mininet driver
Mininet Master driver for B+R PLCs (www.br-automation.com)
Mondial
Modbus RTU and Open Modbus TCP
The driver supports the protocol "Modbus RTU" over a serial connection and over a TCP/IP connection and the protocol "Open Modbus TCP" for TCP/IP connection. The driver acts as a Modbus Master. (For a Modbus Slave please use the Process Gateway)
Mondial
Modbus Energy driver
Open Modbus TCP/IP driver with the following differences compared to the standard Modbus driver: - TCP/IP channel bundling - improved communication with gateways - read and write only for holding register - supports only Open Modbus TCP/IP protocol - Sequence of Events for AREVA MiCOM 126/127, GE Multilin F650, GE Multilin UR-series, ICE NPx800, Schneider MODICON TSX Premium with COSTRONIC Software www.areva-td.com, www.gedigitalenergy.com, www.groupeice.com, www.costronic.ch
MPI
HMI driver
Driver for the MPI->HMI adapter from Siemens or Helmholz
MPI
Hilscher MPI driver
Driver for Hilscher Netlink Adapter (MPI -> TCP/IP) or Hilscher CIF-PB cards. The Netlink Adapter is also available identical in construction from IBH and Helmholz. (http://www.hilscher.com)
MPI
Lauer PCS812
Driver for PCS812 communication box from Lauer for communication via MPI. (www.systeme-lauer.de)
MPI
3964R-RK512
Driver for 3964R/RK512
MPI
S7 CE-MPI
Driver for MPI Siemens CE platform (http://www.open-platform-program.com/products/default.asp)
MPI
S7 driver Softnet
Driver for S7 PLCs via MPI / H1 / Profibus DP / TCP/IP. Based on the software SIMATIC NET (Softnet) from Siemens. (www.siemens.com)
MPI
PC Adapter - Vipa Green Cable
For the serial communication via the Siemens PC adapter / Helmholz PC adapter to Siemens and Vipa PLCs with MPI interface. Alternativ: Serial communication to Vipa PLCs via the Vipa Green Cable to the Vipa PD interface.
MPI
Driver for ESA PCI CIB
Driver for ESA Windows CE terminal including ESA PCI CIB communication card for Windows CE for the communication with PLCs supporting MPI.
MPI
Driver for VIPA CE touchpanel
Driver for communication with VIPA Windows CE Touch Panel with integrated S7-Chip for PLC connected trough MPI.
NARI
IEC 61850 driver
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
NMEA
Driver for NMEA 2000 Bus
Driver to communicate with components connected to a NMEA 2000 bus system. The driver uses the NGT-1 NMEA 2000 to PC Interface from Actisense. (www.actisense.com)
NR Electric
IEC 61850 driver
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
Omron
OMRON driver
Driver for Omron PLCs (www.europe.omron.com)
Omron
Omron FINS
Driver for Omron SYSMAC. FINS = Factory Information Network System (www.europe.omron.com)
OPC
OPC Client V2-0
Driver for the communication with OPC Servers.
OPC
OPC UA Client driver
Driver for comunication with all OPC-UA (Unified Architecture) servers. The driver supports only Data Access (DA). www.opcfoundation.org
Open Modbus
MODBUS Master protocol
Driver for Modbus Master protocol
Open Modbus
MODBUS Slave protocol
Driver for Modbus Slave protocol
OSAI
OSAI TCP/IP driver
Driver for OSAI Soft PLC/CNC based on Windows CE. (www.osai.it)
Otis
Driver for Otis controller
Driver for the connection to an Otis controller (Lift control). The driver only supports reading access. (www.otis.com)
Panasonic
Panasonic serial
Driver for Panasonic (former Matsushita) FPx PLCs (www.panasonic-electric-works.com). The driver also supports modem connection.
Panasonic
Matsushita TCP-IP
TCP/IP driver for Matsushita FPx PLCs via standard network card. (www.matsushita.de)
Phoenix Contact
Interbus S driver
Driver for Interbus S Generation 4, Based on Interbus PC cards from Phönix Contact (www.phoenixcontact.com).
Phoenix Contact
Interbus-S
Driver for Phoenix Contact Interbus Card
Phoenix Contact
Phoenix Contact driver
Direct driver for all ProConOS based Controll systems from Phoenix Contact. Www.phoenixcontact.com
Pilz
PILZ-PSS
Driver for Pilz-PSS PLCs for ST area, FS area is not supported. (www.pilz.com)
Process-Informatik
S5 TCP-IP
Driver for the S5 TCP/IP communication. The driver supports polling (SEND/RECEIVE) and spontaneous communication (FETCH/WRITE). (www.vipa.de, www.siemens.de, www.inat.de, www.process-informatik.de)
Process-Informatik
S7 TCP-IP
Driver for S7 TCP/IP connection via standard network card without additional software. The driver supports Simatic PDiag. (www.siemens.com)
Process-Informatik
S7 driver Softnet
Driver for S7 PLCs via MPI / H1 / Profibus DP / TCP/IP. Based on the software SIMATIC NET (Softnet) from Siemens. (www.siemens.com)
Profibus DP
CP001 Gateway driver
Driver for the Keba / Hilscher Universal Bus Gatway CP001. Supports communication via Profibus, Interbus usw.
Profibus DP
PCS807 Profibus DP
Driver for PCS807 communication box from Lauer for communication via ProfibusDP. (www.systeme-lauer.de)
Profibus DP
Profibus DP Master driver
Developed for special Moeller Profibus DP participant. Also can communicate with other passive Profibus DP participants. Better alternative: zenonLogic with Profibus DP driver.
Profibus DP
S7 driver Softnet
Driver for S7 PLCs via MPI / H1 / Profibus DP / TCP/IP. Based on the software SIMATIC NET (Softnet) from Siemens. (www.siemens.com)
Profibus DP
Hilscher CIF driver
Generic CIF driver for Interbus and Profibus DP cards from Hilscher (www.hilscher.com). The driver can be configured as master or as slave and communicates with the bus participants on the data level without protocol.
Profibus FMS
FMS with PC card from Siemens
Profibus FMS driver. Based on the software SIMATIC NET (Softnet) from Siemens. (www.siemens.com)
Profinet
ProfiNet IO RT
zenonLogic driver for the communication with Profinet devices.
Reis
Reis Robotics driver
Driver for robots of Reis Robotics (www.reisrobotics.com)
Rockwell
Allen Bradley RS-Linx driver
Supports all connections which are available with RS Linx (http://www.software.rockwell.com)
Rockwell
Allen Bradley DF1-driver
For all Allen Bradley PLCs supporting DF1. The driver works half duplex
Rockwell
Allen-Bradley ODVA driver
Ethernet/IP driver for communication via Common Industrial Protocol - CIP from Open DeviceNet Vendor Organisation (ODVA) with Allen-Bradley Control-Logix and Compact-Logix PLCs. (For Micro-Logix PLCs please use the 'AllenBradleyDF1' driver) The driver supports direct browsing of variables from the PLC, offline browsing from projectfile (*.L5K) and blockread/write for all datatypes including structures and arrays. Www.ab.com
RTK Instruments
RTK9000 driver
Driver for serial comunication with a System 9000TS Sequence of Events Recorder or a Series 725B Combined Annunciator and Event Recorder from RTK Instruments (www.rtkinstruments.com)
Saia
SAIA2ND32 driver
Driver for PGU,SBUS, P800, modem, TCP. Whereby communication via TCP is possible with one PLC per driver. (www.saia-burgess.com)
Saia
Saia Directly
Driver for direct SAIA communication via PGU,SBUS, P800 and TCP, but not via modem. No SAIA software needed. (www.saia-burgess.com)
SAT
IEC 60870-5-101_104
Driver for the IEC 60870-5-101 (serial) and the IEC 60870-5-104 (TCP/IP) protocol; a Master (controlling station)
SAT
IEC 61850 driver
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
SAT
IEC 61400-25-4 C
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
Sauter
3964R-RK512
Driver for 3964R/RK512
Schiele
Modbus RTU and Open Modbus TCP
The driver supports the protocol "Modbus RTU" over a serial connection and over a TCP/IP connection and the protocol "Open Modbus TCP" for TCP/IP connection. The driver acts as a Modbus Master. (For a Modbus Slave please use the Process Gateway)
Schiele
Schiele S400
Driver for Systron S400
Schiele
Modbus Energy driver
Open Modbus TCP/IP driver with the following differences compared to the standard Modbus driver: - TCP/IP channel bundling - improved communication with gateways - read and write only for holding register - supports only Open Modbus TCP/IP protocol - Sequence of Events for AREVA MiCOM 126/127, GE Multilin F650, GE Multilin UR-series, ICE NPx800, Schneider MODICON TSX Premium with COSTRONIC Software www.areva-td.com, www.gedigitalenergy.com, www.groupeice.com, www.costronic.ch
Schleicher
3964R-RK512
Driver for 3964R/RK512
Schneider
Modbus RTU and Open Modbus TCP
The driver supports the protocol "Modbus RTU" over a serial connection and over a TCP/IP connection and the protocol "Open Modbus TCP" for TCP/IP connection. The driver acts as a Modbus Master. (For a Modbus Slave please use the Process Gateway)
Schneider
Modicon TSX
Connection to Modicon TSX PLC via Unitelway protocol. (www.schneider-electric.de)
Schneider
Modbus Energy driver
Open Modbus TCP/IP driver with the following differences compared to the standard Modbus driver: - TCP/IP channel bundling - improved communication with gateways - read and write only for holding register - supports only Open Modbus TCP/IP protocol - Sequence of Events for AREVA MiCOM 126/127, GE Multilin F650, GE Multilin UR-series, ICE NPx800, Schneider MODICON TSX Premium with COSTRONIC Software www.areva-td.com, www.gedigitalenergy.com, www.groupeice.com, www.costronic.ch
Schneider
3S v3 driver for PLC Handler
3S V3 driver to communicate to CoDeSys v3 based PLCs via PLC Handler. The driver uses the realtime time stamping in the PLC. Therefore a time synchronisation betwenn PLC and SCADA system is mandatory.
Schweitzer Engineering Laboratories
IEC 61850 driver
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
Schweitzer Engineering Laboratories
SEL Fast Message Protocol
Serial driver for SEL IEDs supporting the Fast Message Protocol. The driver supports Fast Meter (binary data only) and Fast Operate.
SE Elektronic
Modbus RTU and Open Modbus TCP
The driver supports the protocol "Modbus RTU" over a serial connection and over a TCP/IP connection and the protocol "Open Modbus TCP" for TCP/IP connection. The driver acts as a Modbus Master. (For a Modbus Slave please use the Process Gateway)
SE Elektronic
Driver for SE-Elektronic
Driver for the connection to products of SE-Elektronic. (www.se-elektronic.de). The driver supports A, B and C devices
SE Elektronic
Modbus Energy driver
Open Modbus TCP/IP driver with the following differences compared to the standard Modbus driver: - TCP/IP channel bundling - improved communication with gateways - read and write only for holding register - supports only Open Modbus TCP/IP protocol - Sequence of Events for AREVA MiCOM 126/127, GE Multilin F650, GE Multilin UR-series, ICE NPx800, Schneider MODICON TSX Premium with COSTRONIC Software www.areva-td.com, www.gedigitalenergy.com, www.groupeice.com, www.costronic.ch
SE Elektronic
BACnet driver Next Generation
This driver comunicates to one or more BACnet devices (BACnet-Automation stations) using BACnet/IP protocol. The connected BACnet devices have to be operated as BACnet servers. The driver implements only client functionalities.
SEL
IEC 61850 driver
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
Siemens
HMI driver
Driver for the MPI->HMI adapter from Siemens or Helmholz
Siemens
Hilscher MPI driver
Driver for Hilscher Netlink Adapter (MPI -> TCP/IP) or Hilscher CIF-PB cards. The Netlink Adapter is also available identical in construction from IBH and Helmholz. (http://www.hilscher.com)
Siemens
IEC 60870-5-101_104
Driver for the IEC 60870-5-101 (serial) and the IEC 60870-5-104 (TCP/IP) protocol; a Master (controlling station)
Siemens
S5 H1
H1 protocol driver for Siemens S5. H1 resp. "Industrial Ethernet" is the protocol name for the cellular network, which is based on the 7-layer-model of the ISO/OSI standard. (www.vipa.de, www.siemens.de, www.inat.de). At PC you need the PC H1 Driver from INAT.
Siemens
S5 TCP-IP
Driver for the S5 TCP/IP communication. The driver supports polling (SEND/RECEIVE) and spontaneous communication (FETCH/WRITE). (www.vipa.de, www.siemens.de, www.inat.de, www.process-informatik.de)
Siemens
Lauer PCS812
Driver for PCS812 communication box from Lauer for communication via MPI. (www.systeme-lauer.de)
Siemens
PCS807 Profibus DP
Driver for PCS807 communication box from Lauer for communication via ProfibusDP. (www.systeme-lauer.de)
Siemens
FMS with PC card from Siemens
Profibus FMS driver. Based on the software SIMATIC NET (Softnet) from Siemens. (www.siemens.com)
Siemens
3964R-RK512
Driver for 3964R/RK512
Siemens
Siemens S5 PD driver
Driver for the programming interface of the Simatic S5 from Siemens with AS 511 protocol. (www.siemens.com)
Siemens
S7 CE-MPI
Driver for MPI Siemens CE platform (http://www.open-platform-program.com/products/default.asp)
Siemens
S7 TCP-IP
Driver for S7 TCP/IP connection via standard network card without additional software. The driver supports Simatic PDiag. (www.siemens.com)
Siemens
S7 driver Softnet
Driver for S7 PLCs via MPI / H1 / Profibus DP / TCP/IP. Based on the software SIMATIC NET (Softnet) from Siemens. (www.siemens.com)
Siemens
WINAC
Driver for the communication with a Siemens Soft PLC (WINAC). (www.siemens.com)
Siemens
S7 driver for S7-200
Connection to Siemens S7 200 PLCs
Siemens
TI 505 - 545 driver
Driver for Texas Instruments TI 505 / 545. Protocols: TBP,NITP, TCP/IP
Siemens
Siemens Sigmasys driver
Driver for the Siemens Sigmasys fire alarm centre. Spontaneou slave driver based on the GMA Manager (Destination Management System)
Siemens
Siclimat X Decos
Driver for communication with Siclimat X Building Automation System, Siemens AG
Siemens
PC Adapter - Vipa Green Cable
For the serial communication via the Siemens PC adapter / Helmholz PC adapter to Siemens and Vipa PLCs with MPI interface. Alternativ: Serial communication to Vipa PLCs via the Vipa Green Cable to the Vipa PD interface.
Siemens
Driver for ESA PCI CIB
Driver for ESA Windows CE terminal including ESA PCI CIB communication card for Windows CE for the communication with PLCs supporting MPI.
Siemens
Driver for VIPA CE touchpanel
Driver for communication with VIPA Windows CE Touch Panel with integrated S7-Chip for PLC connected trough MPI.
Siemens
IEC 61850 driver
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
Siemens
SoftNet ProfibusDP
Driver for Siemens Profibus Master cards
Siemens
Simotion driver
Driver for S7 Simotion D4x5 connection via standard network card without additional software. Offline variable import from Siemens Scout file possible. (www.siemens.com)
Siemens
IEC-62056-21 Driver
Driver for read out of values from energy meters. The driver uses mode C of IEC 62056-21 specification. The driver supports read only comunication.
Siemens
BACnet driver Next Generation
This driver comunicates to one or more BACnet devices (BACnet-Automation stations) using BACnet/IP protocol. The connected BACnet devices have to be operated as BACnet servers. The driver implements only client functionalities.
Siemens
CTI driver
Driver for CTI PLCs,, Texas Instruments TI 505 PLCs or Simatic 545/555 PLCs. The driver support the protocols CAMP and NITP with Packed Task Codes.
Siemens
IEC 61400-25-4 C
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
Siemens
S7 Spont
Spontaneous driver for Siemens S7 TCP/IP. The driver requires a special handling function block in the PLC
Siemens
integra driver
Driver for communication to Siemens S7 PLCs via the integra standard control room interface from Daimler AG
Siemens
S7-Driver for S7-1200/1500
Driver for PLC series S7-1200 and S7-1500. The driver supports the optimized block access.Supported TIA portal versions: TIA V11 up to SP2 Update 5; TIA V12 up to SP1 Update 4; TIA V13 up to SP1 Update 4;
Sigmatek
SIGMATEK
Connection to Sigmatek products (www.sigmatek.at)
Sigmatek
Sigmatek Lasal Driver
Connection to all Sigmatek PLCs, which can be engineered with the engineering software LASAL.
Sinthesi
PICnet driver
Driver for Sinthesi PICnet PLCs (www.sinthesi.com).The driver uses the SAPP (Sinthesi Asynchronous Packet Protocol) protocol
SNMP
SNMP Driver
Driver for communication with devices supporting SNMP v1 and v2.
SNMP
SNMP driver New Generation
Driver for communication with devices supporting SNMP v1, v2 and v3.
Sprecher Automation
IEC 60870-5-101_104
Driver for the IEC 60870-5-101 (serial) and the IEC 60870-5-104 (TCP/IP) protocol; a Master (controlling station)
Sprecher Automation
IEC 61850 driver
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
Sprecher Automation
IEC 61400-25-4 C
The IEC61850 Client driver. The communication between driver and PLC is based on the IEC 61850 protocol, using server/client services via TCP/IP (profile A1/T1). The driver acts as Client (Master) during communication. The driver supports Reporting (unbuffered and buffered).
SQL
SQL Driver
The driver is used for the bidirectional data exchange with a SQL database supporting ODBC.
SQL
Write variable values in SQL
The driver writes values from selected variables into a dedicated table of a SQL database. The driver communicates via ODBC connection.
straton
straton / zenonLogic driver
Driver for connection to straton or zenonLogic
straton
OPC UA Client driver
Driver for comunication with all OPC-UA (Unified Architecture) servers. The driver supports only Data Access (DA). www.opcfoundation.org
straton
straton NG driver
Driver for communication with straton / zenonLogic PLCs. Replaces straton 32 driver. The driver can use several connections at the same time and uses an improved communication concept.
Telco
Telco200 driver
Telco200Z - Telecontrol central station in combination with telephone communication. Dataexchange for online and historical data is possible. CTi GmbH, www.ctiweb.de
Telemecanique
Modbus RTU and Open Modbus TCP
The driver supports the protocol "Modbus RTU" over a serial connection and over a TCP/IP connection and the protocol "Open Modbus TCP" for TCP/IP connection. The driver acts as a Modbus Master. (For a Modbus Slave please use the Process Gateway)
Telemecanique
Modicon TSX
Connection to Modicon TSX PLC via Unitelway protocol. (www.schneider-electric.de)
Telemecanique
Modbus Energy driver
Open Modbus TCP/IP driver with the following differences compared to the standard Modbus driver: - TCP/IP channel bundling - improved communication with gateways - read and write only for holding register - supports only Open Modbus TCP/IP protocol - Sequence of Events for AREVA MiCOM 126/127, GE Multilin F650, GE Multilin UR-series, ICE NPx800, Schneider MODICON TSX Premium with COSTRONIC Software www.areva-td.com, www.gedigitalenergy.com, www.groupeice.com, www.costronic.ch
Texas Instruments
TI 505 - 545 driver
Driver for Texas Instruments TI 505 / 545. Protocols: TBP,NITP, TCP/IP
Texas Instruments
CTI driver
Driver for CTI PLCs,, Texas Instruments TI 505 PLCs or Simatic 545/555 PLCs. The driver support the protocols CAMP and NITP with Packed Task Codes.
Trend
Trend Driver
Driver for the direct connection to a trend PLC
Trend
Trend NG driver
The driver has the same functionality as driver Trend32. It is however based on driver Trend TCC-Suite. With this it can communicate not only a serial interface but also via all communication types (e.g. TCP/IP, Modem) the TCC-Suite supports (www.trendcontrols.com)
VDMA
VDMA-XML driver
Driver for comunication with devices in packaging and process industry using VDMAXML_P Protocoll e.g.: Laetus components. Www.vdma.org, www.laetus.com
Vipa
HMI driver
Driver for the MPI->HMI adapter from Siemens or Helmholz
Vipa
S5 H1
H1 protocol driver for Siemens S5. H1 resp. "Industrial Ethernet" is the protocol name for the cellular network, which is based on the 7-layer-model of the ISO/OSI standard. (www.vipa.de, www.siemens.de, www.inat.de). At PC you need the PC H1 Driver from INAT.
Vipa
S5 TCP-IP
Driver for the S5 TCP/IP communication. The driver supports polling (SEND/RECEIVE) and spontaneous communication (FETCH/WRITE). (www.vipa.de, www.siemens.de, www.inat.de, www.process-informatik.de)
Vipa
Lauer PCS812
Driver for PCS812 communication box from Lauer for communication via MPI. (www.systeme-lauer.de)
Vipa
S7 TCP-IP
Driver for S7 TCP/IP connection via standard network card without additional software. The driver supports Simatic PDiag. (www.siemens.com)
Vipa
S7 driver Softnet
Driver for S7 PLCs via MPI / H1 / Profibus DP / TCP/IP. Based on the software SIMATIC NET (Softnet) from Siemens. (www.siemens.com)
Vipa
PC Adapter - Vipa Green Cable
For the serial communication via the Siemens PC adapter / Helmholz PC adapter to Siemens and Vipa PLCs with MPI interface. Alternativ: Serial communication to Vipa PLCs via the Vipa Green Cable to the Vipa PD interface.
Vipa
Driver for ESA PCI CIB
Driver for ESA Windows CE terminal including ESA PCI CIB communication card for Windows CE for the communication with PLCs supporting MPI.
Vipa
Driver for VIPA CE touchpanel
Driver for communication with VIPA Windows CE Touch Panel with integrated S7-Chip for PLC connected trough MPI.
Volkswagen
Internal driver with time stamp
Internal driver which gives back every set value as actual value with unchanged value but new time stamp. Status bits for Cause of Transmission are also changed. This guarantees that when writing set values with the same value and same time stamp (VBA/VSTA), the value is recognized as a changed value and is therefore passed on
Vollmer
Telco200 driver
Telco200Z - Telecontrol central station in combination with telephone communication. Dataexchange for online and historical data is possible. CTi GmbH, www.ctiweb.de
Wago
Modbus RTU and Open Modbus TCP
The driver supports the protocol "Modbus RTU" over a serial connection and over a TCP/IP connection and the protocol "Open Modbus TCP" for TCP/IP connection. The driver acts as a Modbus Master. (For a Modbus Slave please use the Process Gateway)
Wago
straton / zenonLogic driver
Driver for connection to straton or zenonLogic
Wago
ThinkIO/IOSystem758
Driver for Wago I/O System 758 (Wago IPC) bzw. Kontron ThinkIO with Windwos CE 5.0
Wago
Modbus Energy driver
Open Modbus TCP/IP driver with the following differences compared to the standard Modbus driver: - TCP/IP channel bundling - improved communication with gateways - read and write only for holding register - supports only Open Modbus TCP/IP protocol - Sequence of Events for AREVA MiCOM 126/127, GE Multilin F650, GE Multilin UR-series, ICE NPx800, Schneider MODICON TSX Premium with COSTRONIC Software www.areva-td.com, www.gedigitalenergy.com, www.groupeice.com, www.costronic.ch
Wago
straton NG driver
Driver for communication with straton / zenonLogic PLCs. Replaces straton 32 driver. The driver can use several connections at the same time and uses an improved communication concept.
Woodhead
Applicom IO configuration
Driver for Applicom IO cards (Direct Link)
zenon system driver
Driver for system variables
zenon System driver for displaying internal project information, network information, hardware information of the PC etc. The driver does not use up I/Os or TAGs.
zenon system driver
Driver for simulator variables
zenon Simulation driver for simulation and internal variables. Variables also can be saved remant. The driver does not use up I/Os or TAGs.
zenon system driver
Driver for Mathematics variable
zenon Mathematics driver. For numerical and binary operations. The driver does not use up I/Os or TAGs.
zenon system driver
Driver for internal variables
Driver for internal variables. Variables can be local resp. global and can be started with an initial value or with the last value (remanence). The driver does not use up I/Os or TAGs.
zenon system driver
Remote Runtime driver
Driver for read only communication to a remote Runtime system. Remote Runtimes will be supported through all versions starting with version 5.50. At the remote system no project adaption is necessary.